Product description
ZOOM-6 self-adhesive film and its modifications to protect plastic surfaces.
Properties
Protective film grade | ZOOM - 6 |
---|---|
Serial color of protective film |
transparent light blue light blue matte green matte |
Serial thickness of the adhesive film, µm | 35;45 |
Serial width of the adhesive film, µm | 50÷1500 |
Serial winding length in roll, MP | 100;500;1000 |
Operating temperature of the protective film, C | -40÷+80 |
Stable adhesion, g/25 mm | 90÷130 110÷150 130÷180 150÷200 210÷250 |
Protective film ZOOM-6 is a light polymer film designated to protect glossy plastic surfaces, as well as a variety of elements of interior decoration. The film is easily and quickly glued in just a few simple steps and remains on the surface for many years.
What does the ZOOM-6 film protect from?
ZOOM-6 reliably protects the surface from the following types of negative environmental effects:
- High humidity
- Wind, dirt, dust
- Mechanical effects: scratching, small bumps, etc.
- Sudden temperature changes
Having pasted elements of the interior with the ZOOM-6 film, you will significantly extend their service life.
What surfaces can be protected with ZOOM-6 film?
This film model is universal and suitable for protection of almost any surfaces:
- Matte, glossy and foamed PVC sheets
- Glossy PVC furniture facade
- Door leaf, solid elements
- Glossy plastic
- Polystyrene sheet (glossy)
- Glossy fiberglass
- Roofing products from PVC (corrugated sheets, drainage system, tile)
- elements of Interior decoration for buses, trains, planes, ships
And many other flat surfaces of civil or industrial construction.
What are the advantages of ZOOM-6 film?
In relation to the majority of competitors, this film model has the following advantages:
- High tensile strength
- High degree of adhesion
- Low price
- 100% of moisture resistance
- Resistance to mechanical damage
- Easy to apply
- Easy to remove (leaves no glue, stains)
Service life
Properly glued film can last more than 30 years without the need for replacement. The components of the film have a high level of resistance to all types of external exposures, as well as to the effects of chemical elements.
Fields of application of ZOOM-6
Polymer protective film is used in most areas of civil and industrial construction. It helps to protect the elements of the drain from corrosion, roofing, interior and exterior finishes.
As a rule, the ZOOM-6 is used to protect interior trim and interior elements. It is characterized by lightness, subtlety and good light conductivity.
How to buy a protective film ZOOM-6?
In order to place an order, you can call us at +7 (831) 413-66-37 or submit your request for a call back through a special form on the website. You can also send a letter with your request to mail zoom-nn@mail.ru and zoom1-nn@mail.ru. Our managers will gladly contact you and answer all your questions. We provide a guarantee of quality on all our products.
Are used to protect:
- Glossy and matte hard and foamed PVC sheet
- Glossy and matte furniture façade of PVC film
- Door leaf of interior door and additional elements
- Glossy ABS plastic sheet and its products
- Glossy polystyrene sheet and its products
- Glossy fiberglass for interior decoration of ships and railway trains
- PVC Roofing products with a smooth surface: profiled flooring, tile, roof drainage system, additional elements
This protective film is available in modification - "film with the seal of the customer's logo."
INSTRUCTION
for intermediate and ultimate users on the protective films of “ZOOM” brand
1. PURPOSE OF THE PROTECTIVE FILM
1.1. The self-adhesive protective film of the “ZOOM” brand is used as temporary packing to protect smooth, matte, textural and other rough surfaces of metal, plastic, glass, wood products from damages at insignificant mechanical effects and pollution during the storage, transportation, installation.
2.TRANSPORTATION OF THE PROTECTIVE FILM.
2.1. Transportation of rolls of a protective film is made on pallets in horizontal or upright position, with obligatory interlining material made of corrugated cardboard between the rolls, in the enclosed transport protected from atmospheric condensation.
2.2. Each packed pallet must have a packing sheet, each rolls – tare label, shipment – certificate of quality.
2.3. Transportation and loading works should be carried out with extreme care to prevent damage to the rolls of protective film for mirrors.
3. STORAGE OF THE PROTECTIVE FILM.
3.1. Protective film of “ZOOM” brand should be stored in rolls in a dry, ventilated area, without direct sunlight, dust and water at a temperature of + 4 to +35 ° C, at a distance of 1 m from the heating devices, without the aggressive vapors, inflammable liquid, refined products and combustion products in the environment.
3.2. The shelf life of the protective film of “ZOOM” brand in the original packaging is 6 (six) months from the date of manufacture while observing storage conditions by the Customer.
4. APPLICATION OF PROTECTIVE FILM ON THE SURFACE OF THE PRODUCT.
4.1. During the application a protective film on the product, it is necessary to ensure the temperature of the protected surface within + 170C = + 350C and the rolling pressure of 5-6 bar, at the same time to use laminating machines with rubber-coated press rollers. This is especially important for polymer surfaces containing a large number of fillers, plasticizers, modifiers and other active additives.
4.2. The surface of the protected product must be dust-free, dry and clean, must have no traces of oils, chemicals and other foreign elements in order to avoid unsatisfactory fixation of the film to the surface of the product or partial transition of the glue when removing the film from the surface of the product. In the case of partial local peeling of the protective film from the surface of the product, it is necessary to increase the pressure and / or equalize the shaft clamp over the entire surface, since acryl is a contact adhesive, the amount of its adhesion to the surface of the product, is directly proportional to the pressure, pressing the film of the gummed shaft. The time interval from the initial adhesion (starting adhesion) to the complete fixation of the protective film on the surface of the product is 24 hours
4.3. If the protective film is exposed to negative temperatures, it must be kept in a warm room for 24 hours to a temperature of at least + 17 °C, throughout the volume of the roll, which will prevent condensation.
5. STORAGE, USAGE THE PRODUCTS WITH A PROTECTIVE FILM.
5.1. The recommended shelf life of the protective film on the surface of the product is up to 4 months from the date of application of the film on the surface of the product till the installation of the product into the structure.
5.2. Storage of the protective film pasted on the surface of the products is carried out indoors, avoiding insolation and moisture exposure, at a distance of 1 m from the heating devices, without the presence of corrosive vapors in the environment, petroleum products and combustion products, in packaged form. When storing outdoors, it is necessary to pack the package with the products with waterproof opaque material.
5.3. The operating temperature range of the protective film on the surface of the product is about 0 -40°C = + 60°C.
6. REMOVAL OF THE PROTECTIVE FILM FROM SURFACE OF THE PRODUCT.
6.1. It is recommended to remove the film from the surface of the product not later than 10(Ten) days for transparent films and not later than 30(Thirty) days for opaque coloured films, after installation of the product into the structure.
6.2. Produce the process of removing the protective film from the surface of the product at temperature of the surface of -10°C to +25°C. Preferably remove the protective film smooth translational movements. If the surface of the film is heated by direct sunlight to a temperature above + 25°C, it is recommended to cool the film with a rag moistened with cold water and only then remove the film with a smooth translational motion. In case you have missed this step and traces of glue are formed on the surface of the protected product, it is recommended that quickly, avoiding dust getting on the sticky surface, wipe the surface with a cloth moistened with solvents from the list, which by the method of selection do not dissolve the polymer surface of the protected product: ethyl acetate, butyl acetate, 646, acetone, Cosmophene solvent, ethyl, methyl and isopropyl alcohol. After that, wash the product with water with detergent. Paint on the colored rags should not dissolve by the above chemicals and leave marks on the surface of the washed product.
6.3. When removing from the surface of the product, it is forbidden to heat the protective film with any heating devices, especially heating devices that emit combustion products.
6.4. Removal of the protective film from the surface of the product begins from the end of the short side of the product, gradually folding the film into a roll along the entire length of the short side to give mechanical strength and convenience to the holdsite of the film, gradually moving to the opposite short end of the product. The effort to remove the protective film in this case, is distributed over the entire width of the protective film, excluding breaks even in places of damage of the protective film.
7. NOTE.
7.1. The properties of the protective film can be lost in case of violation of storage and operation conditions.
7.2. Physical and mechanical parameters of the protective film are valid under test conditions: temperature is 23 +- 1°C, relative degree of humidity 50+- 5%.
7.3. In case of violation of the operation requirements of the protective film, the manufacturer reserves the right not to accept claims relating to quality
7.4. The surfaces of the protected product require a thorough check of compatibility with the adhesive composition. Claims for the quality of the film, if they are the result of incompatibility of the film and equipment, or if during the process of work physical or chemical properties of the product or the surface of the protected product change, are not accepted. The manufacturer of the protected product is obliged to independently undergo tests using its surfaces and to allow the film for the manufacture of its finished products, with the obligatory submission to the address of OOO "ZOOM" positive test certificate of the test sample.
7.5. The following official data are obligatory for consideration of the claim: product brand and standard sizes,serial number, roll number, date of manufacture, photo of the place where the hidden defect spotted.